News

Most people now use the sliding door for the wardrobe . The sliding door is more convenient to use and does not take up space. Now the wardrobe style of the sliding door is also very beautiful, so everyone knows that the wardrobe is pushed and pulled. How should the door track be installed? The following small series will give you a specific introduction, friends who want to know will come and see it! Wardrobe sliding door rail Wardrobe sliding door rails? Installation steps 1. The size of the track box on the upper part of the sliding door should be 12 cm high and 9 cm wide. Like the curtain box, a rail is mounted in the track box to suspend the sliding door from the rail. When the height of the door is less than 1.95 meters, it feels very depressed. Therefore, when doing sliding doors, the height must be at least 195 + 12 = 207 cm. 2. The gold size of the normal door is about 80 cm × 200 cm. Under this structure, the door is relatively stable and beautiful. Therefore, the ratio of the width and height of the sliding door should be similar to the size of the gold. 3. Use the sliding door (bright hanging track box) from floor to top with caution. Since the swing amplitude is too large when pushing and pulling, the sliding door is easily deformed after a long time, and the door cannot be opened after the deformation, which means that it cannot be repaired and cannot be used. 4. Finally, install the sliding door track: fix the upper rail, use the gravity cone (hanging hammer) to hang 3 points on the upper and middle points of the upper rail and draw a 3.3-point surface with the oil pen on the ground, install the upper rail, then Put a hammer to the ground at the center point of the upper track. Vertical lines should be placed at both ends of the track. The lower track is fixed at these three points to ensure that the upper and lower rails are completely parallel, and the sliding of the sliding door is optimal. The state is gone. Wardrobe sliding door slides? Installation precautions Since the sliding door is in contact with the wall or the sides of the cabinet, there is no other object in the contact position to block the closing of the sliding door. For example, the position of the drawer in the cabinet should avoid the intersection of the sliding door and be at least 1cm higher than the bottom plate; the drawer in the folding cabinet should be at least 15cm away from the side wall. Pay special attention to the power switch and socket on the wall. The sliding door should be closed and the position of the switch and socket should be changed. Regardless of the floor on which you make any material, you must ensure that the walls of the door are horizontal and vertical. Otherwise, the door will be skewed after the installation is completed. The adjustable error is no more than 10mm. The above is the installation method of the sliding door of the wardrobe. Now everyone should understand it. The track of the sliding door must be installed. Otherwise, it will be very troublesome in the future. The sliding door will be very used. Not smooth, so everyone must be careful when installing the sliding door track.

When consumers buy wooden doors, they often don't know much about the flat door and buckle door in the shopping guide. The sound of the explanation is vague. I will take everyone to find out what is the flat door and what is the buckle. Line door. Flat door The flat door is a wooden door with a skinless shape. The surface of the door is flat, but it can also be inlaid in a plane. The surface is machined with various patterns, and then painted with paint. The line is recessed down! The buckle door is the kind of big line that looks like it protrudes upward. The flat door has the following features: 1. The process of the flat door is relatively simple, and the production cost is relatively low. It is a wooden door that ordinary people can consume. 2, the flat door has a durable, easy to install, solid board, light weight features, the touch is also relatively smooth, 3. Another feature of the flat door is that it is smooth, generous and easy to clean. It is usually used in the simple and simple home decoration. Buckle door The buckle line door is the middle and upper grade of the solid wood door. The so-called buckle line door is another piece of plate carved out of the flower shape and glued to the door panel, which has a three-dimensional sense. The buckle door is a kind of paint process door. It is based on the solid wood painted door. The wooden door is also called the inlaid door. The process of the buckle door is more complicated than the flat door, so The price is more expensive than the flat door. The buckle door has the following features: 1. The biggest feature of the buckle line door is that the door core is filled with all solid wood, the texture is the strongest, and the hand touch has obvious concave and convex feeling. 2, another feature of the buckle door is that the sense of style will be very strong, with a three-dimensional sense. The shape line itself is an elegant and exquisite piece of art.

The balcony inside the house needs to be beautifully designed and decorated. So what do you think about designing a sliding aluminium door ? What are the friends of this balcony door sliding door? I don`t know, let`s take a look at our balcony door. What are the advantages and benefits of aluminium door design, and what are some of the techniques for installing this balcony door sliding door. I hope that the knowledge about the sliding door of the balcony door can help everyone. First, the advantages of aluminium doors and windows 1. Heavy-duty sliding doors are also an environmentally-friendly door and window. Recyclable materials are also considered green products. Many people should not think of it, and it has excellent heat preservation. Pearl's exhibition uses aerospace-level sealing technology, which has good air tightness and small heat exchange, and has little effect on room temperature. 2. The heavy-duty sliding door adopts the upper and lower rail sliding groove design. It is not only highly sealed, but also waterproof and soundproof. It is also very reliable. It is also very flexible to open. It is suitable for the living room and balcony. Pearl's 160 series heavy-duty sliding doors adopt a three-chamber design, which makes the internal structure more firm and safe, and is highly resistant to 10 wind pressures. 3. In addition to the advantages mentioned above, the sliding door also has many advantages in the accessories. Its material is mostly made of high-quality hardware, which is very user-friendly, and the door operation is very simple. Still very beautiful. Its pulley consists of two sets of two-wheel parallel pulleys and transmission links, which makes the heavy-duty sliding door have a large carrying capacity, and the sliding operation is smoother, and the safety and stability are completely in line with what people want to achieve when they use it. Expected effect. 4. Heavy-duty sliding doors also have many advantages in structure. This type of door mainly uses the upper and lower rail sliding groove design. This design may not be understood by some people, but it can be checked. There are many advantages, mainly the sealing is relatively strong. It also has the effect of waterproof and soundproofing, and it is also very safe. It is also very flexible to open. It is suitable for occasions such as living room and balcony. People say that the door in the house is entering the facade of a family, so the choice in the selection is definitely high. Second, the balcony door sliding door installation skills 1. Suspended sliding door is difficult to handle due to the pre-installation of the track box and tiling, which brings certain difficulties to the construction. Because the track is under a certain pressure, the brick is also stressed. For a long time, it is easy to cause the brick to crack near the track. In addition, in the space such as the kitchen and bathroom (bathroom decoration renderings), the track box is prone to dirt and dirt, and soot and dust are falling on it, causing troubles for cleaning. 2. The size of the track box on the upper part of the sliding door should be 12 cm high and 9 cm wide. Like the curtain (curtain decoration effect) box, the track box is equipped with a track to suspend the sliding door on the track. Most doors or door openings today have a height of 1.95 to 2.15 meters. Experience has shown that when the height of the door is less than 1.95 meters, no matter how tall the person is, it will feel very depressed and uncomfortable. 3. Therefore, when doing the sliding door, the height should be at least 195+12=207 cm. If there is enough space for the track box, you can consider the sliding door. Otherwise, it can only be an external suspension, that is, the track box is exposed outside, which is certainly not beautiful, and the gap between the door and the wall will become larger after a long time. 4. The width of the sliding door is particular. The gold size of the normal door is about 80 cm x 200 cm. Under this structure, the door is relatively stable. If there is a height higher than 200 cm, or even higher, the sliding door should be narrowed or the sliding door should be narrowed to keep the door stable and safe.

The door is the guardian of our family, it is a barrier, it is a landscape. Its subtlety is not only in the intuitive feelings it gives to people, but also in that it brings people a world of infinite reverie. And when you open the door, you really feel that it is your own place, your own world, and your own permanent warmth. This is the more important meaning of its existence. 1. The appearance of solid wood door The solid wood composite door has various shapes and rich styles, or exquisite European-style carved flowers, or classical Chinese colorful mosaics. It has the characteristics of smooth feel and soft color, strong and durable, and it is not easy to crack at the same time. It belongs to middle and high-end products. Today we recommends a high-grade solid wood composite door to you. This solid wood composite door and the wooden door skin oak's strong solid wood sense and bright shape achieve a modern minimalist style. The solid wood composite door inherits the clear texture of the surface layer of the solid wood door, and avoids the disadvantage of the solid wood door being easily deformed. The first sight of the editor of Maxim's Craft Door (left) is thinking about the chocolate milkshake that is about to be deducted. The surface is simulated wood grain mask plastic material, which reminds people of the original bush jungle. The whole door exudes a natural breath. Like a small wooden house in a forest, it is ordinary but not to be ignored. Lemon multi-layer solid wood door is the main product Without too much complicated decoration, the partitions in the middle and lower parts naturally divide the facade visually and only use simple shapes as decoration. In this way, the overall shape is not only beautiful and harmonious, but also meets the visual proportion requirements of our daily door opening. If the overall proportion is not coordinated, then you will feel that the door has no center of gravity, is not stable enough, and will not feel safe. Therefore, in the choice of wooden door style, we must pay attention to the coordination of the split ratio. At the same time, the overall color feels antique. The surface texture is clear, the color is balanced, bright and bright, rich and elegant. Especially suitable for European-style families, demonstrating generous romance. At the same time, other colors or materials can be selected according to the owner's preferences Second, the touch of Maxim's wooden door The surface of craft door is simulated texture plastic material. It can effectively resist aging, scratch resistance, waterproofing, and moisture resistance, and it can form a whole with the door by absorbing plastic in a high-temperature and high-pressure vacuum, forming a natural wood grain shape, beautiful, stylish, and good visual effect. Simulation of wood-grain plastic materials: I used steel brushes to move back and forth on the plastic materials. There is no change in the simulated wood grain material. The door leaf is made of a combination of concave and convex and omnidirectional sealing technology, which is more flavorful than traditional pasting technology. The surface material is the highest-end and most cutting-edge 35-wire ultra-thick artificial wood grain plastic material in the same industry in China, which is a special For anti-theft door and armored door. The editor put his hand on the door and moved back and forth to clearly feel the texture on the door. Because of the simulated wood grain plastic material on the surface, the uneven surface can still feel smooth. (Figure: Internal structure of Maxim's craft door) A in the picture is: it adopts the unique technology in the industry, and the "II" type steel inner rib is added inside the door leaf, which more effectively guarantees the stability of the door and will not be deformed. The door leaf is made of a combination of concave and convex and omnidirectional sealing technology, which is more flavorful than traditional pasting technology. B in the picture is: Moisture-proof board: adopts high-quality moisture-proof panel, which has better collision resistance, the door leaf pattern is updated, the original molding is eliminated, and the advanced computer numerical control engraving process is adopted, which is carefully carved and three-dimensional. It is strong, shows good taste, and has the plasticity and pattern without restrictions. It can meet the personalized design to the greatest extent and provide the owner with a variety of choices. C in the picture is: "II" steel inner rib: how to test if there is steel bar in the door? As long as the magnet is placed on the door, and the magnet does not fall, it proves that there is reinforcement in the door. Internal structure of solid wood door: The interior of solid wood door is a multi-layer solid wood structure, which is made of high density pressed solid wood. 5. Hardware accessories The lock has a metallic silver appearance, which complements the dark facade. Turning the handle is quieter, the lock tongue rotates closely, and the customer can also replace it according to their own preferences. 1. Steel internal ribs and wooden internal ribs are combined with imported high-quality simulated wood grain plastic materials through high temperature and high pressure; 2. The appearance is natural wood grain, no need to paint again; 3. It does not contain formaldehyde and toluene, and meets environmental protection standards; 4. Moisture-proof, heat-resistant, crack-resistant, firm and not deformed; [Environmental protection of Lemon wood door craft door]: Lemon craft door has an important feature --- environmental protection. It does not use the surface painting process of the traditional door industry, and does not allow harmful substances such as formaldehyde and toluene to harm the home. It not only meets domestic environmental standards, but also reaches international environmental standards certification. The material of the door leaf surface is made of 35-wire ultra-thick artificial wood grain plastic material, which is the most advanced and cutting-edge in the domestic industry. This is a special plastic that Lemon Company has anti-theft doors and armored doors. Scratched, waterproof, moisture-proof, and blister in vacuum under high temperature and high pressure to make it form a whole with the door, forming a natural wood grain shape, beautiful, fashionable and good visual effect. The stitching seam is tight, the overall appearance is beautiful and durable. The sealing strip is designed to buffer, reduce noise and sound insulation, while protecting daily wear and tear and increasing its service life.

With the improvement of people`s economic capabilities, most owners` awareness of anti-theft has increased a lot. Therefore, in order to protect the personal safety of the family, installing a american steel door is essential. Then, what are the advantages and disadvantages of the security door with window ? Now let's take a look at it! What are the advantages and disadvantages of steel security door In fact, the door with window is equipped with anti-theft locks. Within a specified period of time, it can resist normal opening under certain conditions. At the same time, it has a certain degree of security protection and a commercial steel door that meets the anti-theft security level. It is reported that the security door is called "anti-theft security door." This shows that it has both anti-theft and security features. According to the "General Technical Conditions for Anti-theft Security Doors," the standard Steel Door are within fifteen minutes. Whether they are using ordinary tools such as screwdrivers, crowbars, chisels, or portable electric tools such as hand drills, there is no way to open them. It is not even possible to open a 615 square millimeter opening in the door leaf, or to open a 38 square millimeter opening in the 150 square millimeter semicircle of the locking point. In addition, the anti-theft door must also be a special anti-theft door lock with anti-drilling function that passes the detection of the Ministry of Public Security testing center. steel security door advantages and disadvantages The door security door is more suitable for installation in the pattern of the house, because it can play a certain ventilation effect. However, its anti-theft and warmth functions will be even worse. If you want to buy a door in the middle of the gate, you must choose the first-class door, because the door in the door that can meet the A-level standard is relatively safer. Therefore, in the question of whether it is OK to make the door in the yard, the owners can decide according to their own taste and pursuit. The disadvantages of the advantages and disadvantages of the security door When the security door is used for a certain period of time, the effect of the ventilation door in the middle will be poor, and the rubber strip will have to be replaced for a long time. However, there are some designs that are special. The ventilation window uses a hundred pages. This kind of installation of a hundred pages can, to a certain extent, block sightlines and ensure smooth airflow, but the ability to isolate sound is relatively weak. In addition, the use of the frosted glass door in the door can effectively block the line of sight, but it will affect the ventilation, so owners do not use the best. Conclusion of the article: We introduced the advantages and disadvantages of the security door and the related knowledge of the door of the yard as the middle door. We hope to give you some help. In fact, if you want to ensure that you live in a safe environment, you can install a security door!

Recently, the technical achievements of the processing-free printing plate-based aluminum plate developed by the China Aluminum Materials Institute and Chinalco Ruimin have been evaluated by experts in the non-ferrous metal industry. The overall technology has reached the international advanced level. Among them, the aluminum profile and anodized quality indicators Reach the international leading level. In order to break through the technological blockade, the China Aluminum Materials Institute and Chinalco Ruimin have carried out a technological breakthrough in the treatment of aluminum alloy sheets for the base of printing plates. After many process verifications in the pilot workshop of China Aluminum Materials Institute, the fundamental reason for the deformation ability and high resolution of the printing plate base was found, and the "alloy composition-preparation process-metal structure-mechanical properties-electrolysis and anodized surface Based on the relationship between morphology and defects, a new type of aluminum alloy plate and strip alloy composition and key preparation technology have been developed, and aluminum alloy plate and strip for processing-free printing plate base have been successfully prepared in Chinalco Ruimin. All performance indicators exceed similar foreign products. Processing-free printing plate base refers to the printing plate base that uses computer to make plates directly and scan and image. Compared with ordinary printing plate bases, it can save steps such as preheating, developing, gluing and baking. It is environmentally friendly and has high deformability. , High resolution, high printing resistance and other advantages, there is a lot of room for development. At present, the non-disposal printing plate base aluminum material is monopolized by foreign companies, and my country is subject to patent and technology blockade. The processing-free printing plate base aluminum alloy sheet developed by China Aluminum Materials Institute and Chinalco Ruimin has filled the domestic gap and realized import substitution. It has a domestic market share of 90%. Some products are exported to Japan and Europe, strengthening Chinalco The Group's core competitiveness in the field of printing plate bases has strengthened the leading and supporting role of technology.

When decorating, the owners are most entangled with the choice of materials. As far as ceramic tiles are concerned, there are many types of ceramic tiles on the market. Glazed tiles and polished tiles are two of the more common types of tiles. What is the difference between them ? Is glazed tile good? 1. Is the glazed brick good? Glazed tile is a special formula glaze that can be polished on the glazed surface. It is the last glaze applied to antique tiles. At present, it is generally transparent glaze or transparent convex flower glaze. Glazed tiles combine the advantages of polished tiles and antique tiles. The glazed surface is as smooth and clean as polished tiles. At the same time, the glazed patterns are rich in patterns like antique tiles, and the colors are thick or gorgeous. 1. Advantages of polished glazed tiles (1) Full polished glaze is a special formula glaze that can be used in the polishing process of the glazed surface. The full polished glazed brick combines the advantages of polished tiles and antique bricks. The glazed surface is smooth and bright like a polished tile. The glazed patterns are rich in patterns like antique bricks, and the colors are thick or gorgeous. (2) The characteristic of the glaze is that it does not cover the top glaze and the various flower glazes under the transparent, only a thin layer of the transparent glaze is thrown away when the glaze is tossed, and the transparent convex flower glaze is used to make the full glaze is the beautiful ceramic Marco Polo Outstanding work, its convex glaze is screen-printed on the brick surface into intermittent convex granular glaze, fired and then glazed, the effect is even more unique. (3) From a technical point of view, there are two main production processes for full-glazed glazes. One is the process used by some companies that originally produced glass-ceramics. It uses the process of printing first and then stacking the glaze. The transparent glaze on the surface is relatively thick. , So the three-dimensional sense is stronger, the transparency is better, and it is easy to polish; in addition, because of its thick glaze, it is easy to throw. The other is a process adopted by the original manufacturer of antique bricks, that is, whether it is an underglaze pattern or a frit on the surface, it is printed. This process has high fidelity and low cost, but it is very difficult when glazing. Easy to reveal. (4) As a brand-new production process, full polished glaze is not so perfect in terms of material, equipment or technical level, such as wear, dirt absorption, bottoming, etc., but the new technology is in continuous development and testing Perfect. 2. Disadvantages of polished glazed tiles (1) Insufficient hardness Although relatively hard and wear-resistant is its advantage, there are generally insufficient hardness of fully polished glazed tiles on the market, which can easily cause scratches and marks on the glazed surface during use; (2) Poor impact resistance The surface of glazed polished tiles is relatively brittle. If they are decorated in passages, walls, etc., they are easily broken by collision; (3) Thin glaze The surface material of glazed tiles is generally thin, and there is still much room for improvement in terms of economy and durability; (4) expensive Because of its outstanding advantages and the market for polished glazed tiles, its price is much more expensive than other tiles, which limits its popularity in home decoration applications. Second, what is the difference between polished glazed tiles and polished tiles 1. Different specifications Polished tiles and glazed tiles are also different in size and size. Polished tiles are mainly used in living room lamps. The size is usually 600, 800 ground tiles, and glazed tiles are often 300 * 300 small. Brick. 2. Different colors The color of the polished tiles is relatively simple, and there is not much change. The difference between the various colors of the brick surface is not too strong, but the polished tiles are different. The polished tiles are more colorful than the polished tiles. The glazed polished tiles are glazed after being printed with patterns, and the colors should be relatively bright, and they are completely unrestricted. Red, black, yellow, blue, and purple are no problem. 3. Different lines The lines of polished tiles and polished tiles are different. The texture of polished tiles cannot be made very small. The polished tiles can achieve fine lines like needlework. 4. Different bricks The brick is the key to distinguish between polished tiles and glazed tiles. Polished tiles penetrate the color into the brick body, so the color of the brick body 1-2mm below the surface is the same as the surface. The glazed tiles are completely different, and will not penetrate into the brick body at all. Looking at the side of the brick, the glazed brick layer is more obvious. It is obvious that the glazed surface can be seen. If the brick surface has only a very thin layer The layer must be glazed tiles. 5. Different wear resistance Glazed tile is a layer of glaze added to the surface of the polished tile. In contrast, the brightness is good and the permeability is good, but the wear resistance is not as good as the polished tile. The surface of the polished tile is very thick with crystals, which is relatively wear-resistant, while the surface of the polished tile is glazed, which is very thin, and its wear resistance is not so strong. 6. Different stain resistance Polished tiles are suitable for use in most indoor spaces except for toilets and kitchens, but the uneven pores left by the polished tiles during production will hide dirt and dirt, causing the surface to easily infiltrate contaminants and even some tea poured in The polished tiles are weak, and the anti-pollution effect of the polished tiles is far more than that of the polished tiles. 7. Different prices Glazed tiles have a high degree of simulation. It combines the advantages of antique tiles and polished tiles. The tiles are polished on the basis of glazed tiles. The process is more complicated than polished tiles. The appearance has both rich colors and polish of glazed tiles. The brick is bright and clean, so the price is more expensive than the polished brick. Editor's quote: Is the polished glazed brick good or not, what is the difference between the polished glazed brick and the polished brick? In short, the glazed polished brick has its advantages and disadvantages. The editor recommends that you carefully understand when choosing materials to avoid negative effects on the decoration. What, the decoration still uses his own money? ! The Qi family is decorated in installments, with an ultra-low annual interest rate of 3.55% and a maximum loan of 1 million. Apply now to enjoy the discount If you are interested in brand cooperation, content cooperation, and advertising of this website, please send an email to sales07@lemonbuilding.com

How to care for solid wood paint door Nowadays, owners are demanding more and more doors during the renovation process. In order to improve the quality of life, it is very important to buy a suitable solid wood door paint door, because the solid wood door paint door appearance atmosphere, and its use time will be longer than the average door, line surface Xiaobian introduce the advantages of solid wood doors paint the door of solid wood doors paint the door and introduce how to care. First, the advantages of solid wood door paint door 1. The solid wood door painting door is very exquisite in terms of craftsmanship, and the materials are made of high-quality wood. The outer core of the exterior material adheres tightly, and at the same time, it is not easy to crack, and the paint surface is refined and beautiful. 2, solid wood door paint doors made of very rich style, texture clear and beautiful, with a particularly good three-dimensional, but also touch the feel is not bad, can be used with different home decoration, adaptability. 3, if the appearance of damage in daily use, only need to invite professional workers to repair, solid wood door paint door can be restored to the state just after purchase, and repair is particularly simple. 4, solid wood door paint door prices are very close to the people, it is suitable for everyone to buy. 5, solid wood door paint door can be produced in accordance with the individual preferences of users, also includes the size of the area, color, style, etc., can be customized according to individual requirements. 6, this type of door can be very good to get the problem of workmanship in the processing of solid wood doors, for example, split at the mouth, the door core board shrinkage and other shortcomings. 7. After a long time of using the solid wood door paint door, there will be no appearance cracks and discoloration, and it has the advantages of moisture proof and anti-deformation. Second, solid wood door paint door how to care 1. When the door is opened and closed during daily use, try to lighten the door, and do not hang too heavy on the door to avoid reducing the use time. 2, daily cleaning, can use cotton cloth to clean, do not use a hard cloth, or else it will damage the appearance, if the dirt is too difficult to clean, you can use a soft detergent, etc., remove the dirt and then wipe with a cloth. Do not wash directly with water or use a damp rag to clean it. Avoid wooden arch deformation. 3, in the routine maintenance can not be too much friction, or else it will lead to spearhead paint drop. 4. When the weather temperature is different, if it is found to have cracks or shrinkage, do not panic. This is normal, no need to be nervous, it will change with the seasonal, this phenomenon will disappear naturally. Summary: The above is the introduction of the advantages of solid wood door paint door introduced by Xiao Bian and the related knowledge of how to maintain the solid wood door paint door. I hope we can help everyone! I believe we have a deeper understanding of solid wood door painting door after reading. To know more about the relevant knowledge, please continue to pay attention to this site.

Today's decoration home Xiaobian introduced to you the relevant content of the security door. Speaking of the security door, I have to say that it is really a good thing. Not only can we protect the safety of our family but also protect our property, we can also reduce the chance of burglary. Nowadays, people's lives are getting better and better, and the awareness of anti-theft is gradually increasing. It is also necessary to install security doors. Then the following small series will introduce how the security door is: First, the installation points (1) The installation of the security door should be in accordance with the type of security door used, and the appropriate installation method should be adopted. (2) The door frame of the anti-theft door can be fixed with the expansion bolt and the wall body. The iron piece can be pre-embedded at the hole when the wall is built, and the door frame connecting piece is welded firmly during installation. (3) Regardless of the connection method used for the door frame and the wall, there should be no less than 3 anchor points on each side and should be firmly connected. (4) When installing the security door, it should be straightened and hanged first. After the size is appropriate, temporarily fix it and correct it and adjust it. After the error is correct, the connection can be anchored. (5) It is required that the sliding door can be pushed and pulled flexibly after installation; the swinging door is convenient to open, the closing is tight and firm, and there is no self-opening phenomenon. (6) Anti-theft device should be installed between the door frame and the door leaf or other parts. (7) Hardware accessories such as handles, door locks, and observation holes on the security door must be complete; the password protection lock, electronic alarm password system, doorbell paging and other devices on the multi-function security door must be effectively improved. (8) The clearance from the ground plane should be no more than 5mm. Second, the material of the security door Steel It can be said that it is the most seen in the market and the most used by the people. Most of the security doors familiar to the people belong to this series. Such doors are cheaper and more reasonable, and their sales account for more than 90% of total market sales. The disadvantage of this type of door is that the outer lines are hard and difficult to integrate with modern interiors. 2. Steel door It is a kind of door that can be used for interior decoration. It can be requested by the user. The anti-theft performance is achieved by the middle steel plate. The manufacturer can choose different colors, wood, lines and patterns according to the user's requirements. It is no longer as cold and uncoordinated as a steel door. Therefore, its price is also more expensive than steel security doors. 3. Aluminum alloy The aluminum alloy material used in this kind of door is different from the ordinary aluminum alloy door and window that we have seen. Its hardness is high and the color is bright, and it is decorated with a pattern to give a golden feeling. It is a mid-range security door. Because this kind of door is not easy to fade, it also has a certain consumer group. 4. Stainless steel The stainless steel security door is rugged and safer. The market stainless steel security door has many colors, such as silver white, yellow titanium gold, rose gold, red titanium gold, black titanium gold, rose red, and many other colors. There are also stamping patterns. The pattern of general steel security doors is in stainless steel doors. Generally, it can be realized. The price of stainless steel doors on the market ranges from 400 to 700, depending on whether the material is 201 or 304. It is best to choose a larger stainless steel door to be closer to the installation location, and it is convenient to make the price after sale. 5. Copper Most of the copper security doors combine the traditional anti-theft and the entrance door into one, with advanced styles, and have good performance in fireproof, anti-corrosion, anti-mite and dustproof. From the material point of view, the copper security door is the best, from the price point of view, it is also the most expensive, the basic price that can be seen in the market is more than 10,000 yuan, the most expensive up to hundreds of thousands of yuan. It is mainly used by financial institutions such as banks or high-end residential villas. Security door purchase is not a simple task, it needs to be considered from many aspects, the most important of which is the performance of the security door, which directly determines its anti-theft level. Generally, it mainly depends on whether it has the "anti-theft security door" sign, the security door level, the anti-theft door lock core, and the anti-theft door filler. If you want to know more about decoration, please continue to pay attention to the decoration home network. More related wonderful reading: The steps to install the security door introduce the precautions for installing the security door. Top ten security door brands introduce ten major security door brands to buy Which is better? How to buy a security door? What kind of security door is it? What are the types of security doors? Can the security door be locked? What is the price of the security door lock?

Nowadays, when many families are decorating their new homes, they will choose beautiful, atmospheric and high-grain wooden doors, but many people have made it difficult to face different styles and styles of wooden doors in the market. The bedrooms, kitchens, bathrooms and so on. Have your own attributes, what should you pay attention to when selecting doors in different locations? Bedroom door The bedroom is a place to rest, and it is necessary to provide a quiet enough sleeping environment for people to fall asleep quickly. Therefore, the material can be selected from the mainstream solid wood composite door on the market, which not only has various functions such as moisture proof and deformation resistance, but also Very good sound insulation, can guarantee the quality of family sleep. In color, try to use dark-colored doors, which is easy to calm and help sleep. Kitchen door In the choice of kitchen doors, wooden doors with transparent or frosted materials are a good choice, not only for light transmission, but also for fear of soot, corrosion resistance and easy cleaning. Bathroom door The first bathroom is best to use wooden doors with glass, because the glass itself is waterproof, water vapor does not penetrate into the interior of the door, and in the lighting, the glass door helps to make the dim bathroom brighter; secondly, it is matched It should be consistent with the whole bedroom style, the color can not be too close to the floor color, you can choose white or wood color. Choosing a hidden door at home will definitely bring you a lot of practical and unexpected places in life. Of course, the use of invisible doors should be consistent with the wall in color, achieving an "invisible" effect, and the function should be a wall. Face and wooden door. Entry door The entrance door is the first barrier for the family to be external, and it is also the first impression. Under the premise of ensuring security and theft, it is also necessary to show the beauty and fashion, and coordinate with the decoration style of the whole home. Therefore, the choice of the entrance door can be iron, stainless steel, wood, etc., and the color is matched with the color of the furniture.